[ Pobierz całość w formacie PDF ]
the 0 dB position
0.01
0.01
With the volume control at the 10 dB position
With the volume control at the 0 dB position
0.001
0.001
10 100 1000 10000 100000 4 5 6 7 8 9 10 11
Supply voltage, VDD V
Frequency, f Hz
THD - Supply Voltage Characteristics (2)
THD - Input Level Characteristics (1)
1
VSS = 0 V
10
VDD = 9 V
VIN = 10 dBV
VSS = 0 V
f = 1 KHz
100 kHz low-pass
100 kHz low-pass weighting
weighting
1
All tone control settings flat
0.1 All tone control settings
flat
0.1
With the volume control at the 10 dB position
f = 20 KHz
0.01
0.01
f = 1 KHz
With the volume control at the 0 dB position
0.001
0.001 -20 -15 -10 -5 0 5 10
4 5 6 7 8 9 10 11
Input level, VIN dBV
Supply voltage, VDD V
No. 6270-19/20
Gain, G dBV
Volume attenuation dB
Gain, G dBV
Total harmonic distortion, THD %
Total harmonic distortion, THD %
Total harmonic distortion, THD %
Total harmonic distortion, THD %
Total harmonic distortion, THD %
LC75341, 75341M
THD - Input Level Characteristics (1)
10
1
0.1
f = 20 KHz
0.01
f = 1 KHz
VDD = 9 V
0.001
VSS = 0 V
-20 -15 -10 -5 0 5 10
100 kHz low-pass weighting
Input level, VIN dBV
All tone control settings flat
With the volume control at the
10 dB position
Specifications of any and all SANYO products described or contained herein stipulate the performance,
characteristics, and functions of the described products in the independent state, and are not guarantees
of the performance, characteristics, and functions of the described products as mounted in the customer s
products or equipment. To verify symptoms and states that cannot be evaluated in an independent device,
the customer should always evaluate and test devices mounted in the customer s products or equipment.
SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all
semiconductor products fail with some probability. It is possible that these probabilistic failures could
give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire,
or that could cause damage to other property. When designing equipment, adopt safety measures so
that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective
circuits and error prevention circuits for safe design, redundant design, and structural design.
In the event that any or all SANYO products (including technical data, services) described or contained
herein are controlled under any of applicable local export control laws and regulations, such products must
not be exported without obtaining the export license from the authorities concerned in accordance with the
above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system,
or otherwise, without the prior written permission of SANYO Electric Co., Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the Delivery Specification
for the SANYO product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not
guaranteed for volume production. SANYO believes information herein is accurate and reliable, but
no guarantees are made or implied regarding its use or any infringements of intellectual property rights
or other rights of third parties.
This catalog provides information as of December, 1999. Specifications and information herein are
subject to change without notice.
PS No. 6270-20/20
Total harmonic distortion, THD %
[ Pobierz całość w formacie PDF ]